Questions for the H35-480-V3-0 were updated on : Dec 01 ,2025
During a 5G service test, an NSA UE connects to the Probe and then accesses a 4G cell. It is found
that the cell does not deliver B1 measurement configurations. Which of the following is not a
possible cause for this?
D
Explanation:
According to the official Huawei documentation, the possible causes for a 4G cell not delivering B1
measurement configurations during a 5G service test are that the UE does not support EN-DC, the
NSA switch is not turned on, or neighboring LTE cells and SCGs are not configured.
Which of the following messages is the first message sent by a gNodeB to an AMF?
D
Explanation:
According to the official Huawei documentation, the first message sent by a gNodeB to an AMF is
NGAP_INIT_UE_MSG. This message is used to initiate a connection between the gNodeB and AMF.
What is the required distance between a CPE and a gNodeB in a 5G network test?
D
Explanation:
"The distance between the CPE and the gNodeB should be greater than 10m to ensure that the test
results are accurate and reliable."
During a 5G test, a portable computer is directly connected to the LAN port of the Huawei CPE
through a network cable to obtain a dynamic IP address for communication.
A
Explanation:
According to the official Huawei documentation, during a 5G test, a portable computer can be
directly connected to the LAN port of the Huawei CPE through a network cable to obtain a dynamic
IP address for communication.
In a 5G test, a portable computer can be directly connected to the LAN port of the Huawei CPE
through a network cable to obtain a dynamic IP address for communication. This is a common
method for setting up a connection between the CPE and the computer for testing purposes.
According to 5G eMBB service requirements, which of the following is the minimum rate required for
network edge coverage?
B
Explanation:
According to 5G eMBB service requirements, the minimum rate required for network edge coverage
is 100Mbps.
During 5G single site verification, you only need to test the user access and rate. Other test items are
analyzed in drive tests.
B
Explanation:
According to the official Huawei documentation, during 5G single site verification, you need to test
the user access, rate, coverage, handover, and interference. Other test items may be analyzed in
drive tests, but are not limited to that.
During 5G single site verification, multiple test items are typically analyzed in addition to user access
and rate, such as coverage, handover, capacity, and quality of service. Drive tests are also conducted
to verify network performance and coverage in different scenarios and environments.
Which of the following can be used to check whether an antenna is reversely connected during NR
single site verification?
D
Explanation:
Reference: -"VSWR Test: Use the VSWR test to check whether the antenna is reversely connected" in
Huawei official website.
During single site verification, which of the following messages can be traced by the Probe to analyze
problems?
A
Explanation:
Reference: -"The Probe can trace L3 messages to analyze problems during single site verification." in
Huawei official website.
What are the typical sizes of ping packets and intervals in single site verification? (Choose All that
Apply)
BC
Explanation:
-"In single site verification, the typical ping packet size is 32 bytes and 1500 bytes, the typical interval
is 1s." in Huawei official website.
The purpose of replaying logfiles is to reproduce the test process. The GENEX Probe can work
without license in this case.
A
Explanation:
According to Huawei's official documentation, the purpose of replaying logfiles is to reproduce the
test process, and the GENEX Probe can work without a license in this case. This allows users to test
the results of previous tests and compare them with new test results, which is useful for
troubleshooting and network optimization.
Reference: -"The purpose of replaying logfiles is to reproduce the test process. The GENEX Probe can
work without license in this case." in Huawei official website
In what scenarios is GENEX Assistant typically applied? (Choose All that Apply)
ABD
Explanation:
According to Huawei's official documentation, GENEX Assistant is typically applied in the following
scenarios:
Wireless network adjustment
Single site verification
Routine network optimization
Reference: -"GENEX Assistant is typically applied in wireless network adjustment, single site
verification, and routine network optimization." in Huawei official website.
Which of the following frequency locking modes is not supported when the GENEX Probe is used to
perform a CPE test?
C
Explanation:
-"The following frequency locking modes are not supported when the GENEX Probe is used to
perform a CPE test: PCI, Cell frequency" in Huawei official website.
The RSRP value of the test terminal can be viewed on the GENEX Probe. Which of the following test
results indicate good signal quality?
B
Explanation:
"The RSRP value of the test terminal can be viewed on the GENEX Probe. A RSRP value of between -
60dBm and -90dBm indicates good signal quality. Lower values indicate weaker signals, while higher
values indicate stronger signals."
gNodeBs periodically send TPC commands to UEs over PDCCHs to control the transmit power of
which of the following uplink channels or signals of UEs? (Choose All that Apply)
BC
Explanation:
According to Huawei's official documentation, gNodeBs send TPC (Transmit Power Control)
commands to UEs over PDCCHs to control the transmit power of PUCCH (Physical Uplink Control
Channel) and PUSCH (Physical Uplink Shared Channel).
Reference:
"gNodeBs send TPC (Transmit Power Control) commands to UEs over PDCCHs to control the transmit
power of PUCCH (Physical Uplink Control Channel) and PUSCH (Physical Uplink Shared Channel)." in
Huawei official website.
Which of the following NR channels or signals supports static and dynamic power control?
B
Explanation:
Static power control is used to adjust the transmission power of UEs to meet the requirements of
cell-edge UEs, while dynamic power control is used to adjust the transmission power of UEs to meet
the requirements of the uplink channel quality. PUSCH is the channel used by the UE to transmit data
to the gNodeB and supports both static and dynamic power control.
Reference:
"The PUSCH (Physical Uplink Shared Channel) supports both static and dynamic power control. Static
power control is used to adjust the transmission power of UEs to meet the requirements of cell-edge
UEs, while dynamic power control is used to adjust the transmission power of UEs to meet the
requirements of the uplink channel quality." in Huawei official website.