dell D-NWG-FN-23 Exam Questions

Questions for the D-NWG-FN-23 were updated on : Nov 21 ,2025

Page 1 out of 4. Viewing questions 1-15 out of 60

Question 1

In the OS10 CLI what does Ctrl+A do?

  • A. Deletes all the text before the cursor.
  • B. Moves the cursor to the start of the command line.
  • C. Moves the cursor to the end of the command line.
  • D. Deletes the word before the cursor.
Answer:

B

User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
vote your answer:
A
B
C
D
0 / 1000

Question 2

At which layer does LLDP operate?

  • A. 1
  • B. 3
  • C. 2
  • D. 4
Answer:

C

User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
vote your answer:
A
B
C
D
0 / 1000

Question 3

What type of network in a Data Center flattens the core and aggregation layers into a single tier?

  • A. Leaf
  • B. Leaf-spine
  • C. Spine
  • D. TRILL
Answer:

B

User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
vote your answer:
A
B
C
D
0 / 1000

Question 4

Which field in an IP header is used for QoS marking?

  • A. ToS
  • B. SA
  • C. CoS
  • D. DA
Answer:

A

User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
vote your answer:
A
B
C
D
0 / 1000

Question 5

Which router types are contained in a single-area OSPF implementation?

  • A. Stub router and ABR
  • B. ABR and ASBR
  • C. Internal router and ASBR
  • D. Backbone router and Internal router
Answer:

D

User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
vote your answer:
A
B
C
D
0 / 1000

Question 6

From which range can a network administrator choose when setting the RSTP priority value?

  • A. 1-6400
  • B. 0-61440
  • C. 0-614400
  • D. 1-64
Answer:

B

User Votes:
A
50%
B
50%
C
50%
D
50%

Reference:
https://www.dell.com/support/article/en-my/how10394/how-to-manage-rapid-
spanning-tree-rstp- thru-command-line-on-dell-networking-powerconnect-switches?lang=en

Discussions
vote your answer:
A
B
C
D
0 / 1000

Question 7

Which commands are required to properly configure an OS10 switch to run OSPF on eth1/1/3 and to
add network 144.254.1.0/30 to OSPF area 0?

  • A. OS10(config)# interface ethernet 1/1/3 OS10(conf-if-eth1/1/3)# no shutdown OS10(conf-if- eth1/1/3)# no switchport OS10(conf-if-eth1/1/3)# ip address 144.254.1.2/30 OS10(conf-if-eth1/1/3)# ip ospf 1 area 0.0.0.0 OS10(config)# router ospf1
  • B. OS10(config)# router ospf 1 OS10(config-router-ospf-1)# router-id 1.1.1.1 OS10(config)# interface ethernet 1/1/3 OS10(conf-if- eth1/1/3)# no shutdown OS10(conf-if-eth1/1/3)# no switchport OS10(conf-if-eth1/1/3)# ip ospf 1 area 0.0.0.0
  • C. OS10(config)# interface ethernet 1/1/3 OS10(conf-if-eth1/1/3)# no shutdown OS10(conf-if-eth1/1/3)# ip address 144.254.1.2/30 OS10(conf-if-eth1/1/3)# no switchport OS10(conf-if-eth1/1/3)# ip ospf 1 area 0.0.0.0 OS10(config)# router ospf 1
  • D. OS10(config)# interface ethernet 1/1/3 OS10(conf-if-eth1/1/3)# no shutdown OS10(conf-if-eth1/1/3)# ip address 144.254.1.2/30 OS10(conf-if-eth1/1/3)# no switchport OS10(conf-if-eth1/1/3)# ip ospf 1 area 0.0.0.0 OS10(conf-if-eth1/1/3)# router ospf 1
Answer:

C

User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
vote your answer:
A
B
C
D
0 / 1000

Question 8

What benefit does VRRP version 3 provide over VRRP version 2 in OS10?

  • A. Provides preemption capability.
  • B. Provides MD5 authentication.
  • C. Allows subsecond timers.
  • D. Allows multiple masters in the topology.
Answer:

C

User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
vote your answer:
A
B
C
D
0 / 1000

Question 9

When installing OS10 on a switch from a USB drive, what format is used for the file system?

  • A. HFS+
  • B. FAT32
  • C. NTFS
  • D. HFS
Answer:

B

User Votes:
A
50%
B
50%
C
50%
D
50%

Reference:
https://www.dell.com/support/article/en-hr/how12762/dell-emc-networking-how-to-
update-os10-on- a-switch-running-os10?lang=en

Discussions
vote your answer:
A
B
C
D
0 / 1000

Question 10

A network administrator wants servers to avoid spanning-tree convergence immediately after
connecting to a leaf switch. Which spanning-tree feature would allow this?

  • A. spanning-tree vlan priority 0
  • B. spanning-tree port-type disabled
  • C. spanning-tree port-priority 0
  • D. spanning-tree port-type edge
Answer:

D

User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
vote your answer:
A
B
C
D
0 / 1000

Question 11

When configuring VRRP in tandem with VLT, what is the default VRRP mode?

  • A. active-active
  • B. primary-standby
  • C. active-standby
  • D. master-backup
Answer:

D

User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
vote your answer:
A
B
C
D
0 / 1000

Question 12

How are ACLs processed?

  • A. LIFO
  • B. FIFO
  • C. Randomly
  • D. Sequentially
Answer:

D

User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
vote your answer:
A
B
C
D
0 / 1000

Question 13

On what does PBR base routing decisions?

  • A. Dijkstra Algorithm
  • B. Batch traffic
  • C. Administrator-defined forwarding
  • D. Shortest path
Answer:

C

User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
vote your answer:
A
B
C
D
0 / 1000

Question 14

What is a feature of virtual routing and forwarding (VRF)?

  • A. Provides trunks that can be grouped to provide optimum speed.
  • B. Allows multiple user groups to co-exist within the same router at the same time.
  • C. Allows different physical switches to operate as one.
  • D. Allows multiple instances of routing tables to co-exist within the same router at the same time.
Answer:

D

User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
vote your answer:
A
B
C
D
0 / 1000

Question 15

What is a valid OS10 iBGP configuration?

  • A. S2(config)# router bgp 64507 S2(config-router-bgp-64507)# peer-as 64507 S2(config-router-bgp-64507)# neighbor 192.168.32.1 S2(config-router-neighbor)# update-source loopback 0 S2(config-router-neighbor)# no shutdown
  • B. S2(config)# router bgp 64507 S2(config-router-bgp-64507)# neighbor 192.168.32.1 S2(config-router-bgp-64507)# remote-as 64507 S2(config-router-bgp-64507)# update-source loopback 0 S2(config-router-bgp-64507)# no shutdown
  • C. S2(config)# router bgp 64507 S2(config-router-bgp-64507)# neighbor 192.168.32.1 S2(config-router-neighbor)# remote-as 64507 S2(config-router-neighbor)# update-source loopback 0 S2(config-router-neighbor)# no shutdown
  • D. S2(config)# router bgp 64507 S2(config-router-bgp-64507)# remote-as 64507 S2(config-router-bgp-64507)# neighbor 192.168.32.1 S2(config-router-neighbor)# update-source loopback 0 S2(config-router-neighbor)# no shutdown
Answer:

C

User Votes:
A
50%
B
50%
C
50%
D
50%

Reference:
https://www.dell.com/support/manuals/us/en/04/networking-z9100/os10-enterprise-
user-guide- 10_4_1-pub/enable-bgp?guid=guid-5c64be15-4ebd-4372-a442-67f47b0f14e5&lang=en-
us

Discussions
vote your answer:
A
B
C
D
0 / 1000
To page 2