cisco 350-601 Exam Questions
Questions for the 350-601 were updated on : Dec 01 ,2025
Page 1 out of 13. Viewing questions 1-15 out of 190
Question 1
An engineer must recover the Cisco UCS system. The full backup is available on a backup SCP server.
Which set of actions recovers the configuration of the Cisco UCS Manager?
- A. Create a scheduled restore job. Reboot the UCS Manager.
- B. Create an import-config task Set the action to Replace.
- C. Factory reset the fabric interconnect. Select the Restore feature.
- D. Copy the backup file to a USB drive. Copy the running-config.
Answer:
A
Question 2
An engineer must upgrade the server firmware for which the service profile is configured with a host
firmware package. Which action must be taken to accomplish this goal?
- A. Change the maintenance policy to user-ack and upgrade.
- B. Perform a direct upgrade on the server using Auto Install.
- C. Disassociate the service profile from the server and upgrade.
- D. Upgrade the server through the host firmware package.
Answer:
B
Question 3
An engineer must configure Protocol Independent Multicast on two Cisco Nexus 9000 Series
Switches. The engineer must ensure that the chosen rendezvous point (RP) uses a mapping agent
and only supports one RP per multicast group. Which type of RP must be used on both switches to
meet these requirements?
- A. bootstrap router
- B. static
- C. Auto-RP
- D. Anycast-RP
Answer:
A
Question 4
An engineer must deploy a new Cisco MDS 9000 Series Switch and be able to receive
LinkUp/LinKDown notifications that were sent using a secure industry standard. Which technology
must be used to accomplish this goal?
- A. PMON
- B. SPAN
- C. RMON
- D. SNMP
Answer:
D
Question 5
An engineer must configure a Cisco MDS 9000 Series Switch for traffic analysis from the storage array.
The storage array is connected to the interface fc2/1 in VSAN 10 and the traffic analyzer to fc4/2. The
capture file must include ingress and egress traffic between the switch and the storage array. Also,
only traffic in VSAN 10 must be captured. Which configuration set meets these requirements?
- A. interface fc4/2switchport mode SD no shutdown!span session 1 source interface fc2/1 destination interface fc4/2 source filter vsan 10
- B. Interface fc4/2switchport mode trunk switchport trunk allow vsan 10 no shutdown!span session 1 source interface fc2/1 tx destination Interface fc4'2 rx no suspend
- C. Interface fc4/2switchport mode auto no shutdown!span session 1 source interface fc2/1 rx destination interface fc4/2 source filter vsan 10 no suspend
- D. interface fc4/2 switchport mode STno shutdown!span session 1 source interface fc2/1 destination interface fc4/2 source filter vsan 10
Answer:
D
Question 6
Which two Cisco UCS components are upgraded when using Install Infrastructure Firmware? (Choose
two.)
- A. Cisco UCS Manager
- B. board controller
- C. I/O modules
- D. storage adapters
- E. BIOS
Answer:
A,C
Question 7
Refer to the exhibit. An engineer must connect a Cisco MDS Series Switch to a Cisco UCS domain
using a port channel, but the link fails to activate. Which command activates the interface?
- A. switchport speed 8000
- B. switchport trunk mode off
- C. switchport rate-mode shared
- D. switchport mode F
Answer:
A
Question 8
Refer to the exhibit.
An engineer must replace the Fabric Interconnect called UCS-FI LAB1 with the Fabric Interconnect
called UCS-Fl LAB2. The new Fabric Interconnect must be restored with the latest configuration of
UCS-Fl LAB1. Which backup type must be used to meet this requirement?
- A. All configuration
- B. Logical configuration
- C. Full state
- D. System configuration
Answer:
D
Question 9
An engineer must assign a device alias of Marketing to a Fibre Channel port that has a world wide
name of 21:00:00:00:11:11:22:22 on a Cisco MDS 9000 Series Switch. Which two commands
accomplish this goal? (Choose two.)
- A. Option A
- B. Option B
- C. Option C
- D. Option D
Answer:
AB
Question 10
Refer to the exhibit.
Two Cisco Nexus Series Switches use EIGRP between their Eth1/1 interfaces. The switches are
configured to support EIGRP authentication. Which set of CLI
commands must be used to establish EIGRP neighborship?
- A. interface Ethernet1/1 ip router eigrp Pallini ip authentication mode md5 Pallini EIGRP
- B. Interface Ethernet1/1 ip router eigrp 10 ip authentication mode eigrp Pallini EIGRP
- C. interface Ethernet1/1 ip router eigrp 10 ip authentication mode EIGRP Paliini md5
- D. interface Ethernet1/1 ip router eigrp Pallini ip authentication mode eigrp Pallini md5
Answer:
D
Question 11
A company plans to migrate some of its services to the cloud. The company does not want to
manage or control the underlying cloud infrastructure. It also wants to maintain control over the
deployment of its applications and configuration settings of the application-hosting environment.
Which cloud service model meets these requirements?
- A. Platform as a Service
- B. Function as a Service
- C. Infrastructure as a Service
- D. Software as a Service
Answer:
A
Question 12
An engineer must perform a backup and restore in Cisco UCS to rebuild the system in a disaster
recovery scenario. The backup file must be encrypted to prevent the passwords from being
stored as cleartext. Which backup configuration meets these requirements?
- A. Full state backup over TFTP
- B. All configuration backup over SFTP
- C. System configuration backup over FTP
- D. Logical configuration backup over SCP
Answer:
A
Question 13
A customer deploys a media server to distribute streaming videos to network clients. The
requirement is to allow the video feed to reach only requesting clients. The shared trees must not
propagate the video feed if no clients from that tree request it. To reduce configuration touchpoints,
the solution must support the automatic discovery and announcement of RP-set
information. Each router in the network is responsible for selecting the RP. Which configuration set
meets these requirements?
- A. router(config-if)# ip pim sparse-sense mode router(config}# ip pim auto-rp router(config)# ip pim send-rp-announce
- B. router(config-if}# ip pim dense-mode router(config)# ip pim rp-address 1.1.1.1 router(config}# ip pim rp listener
- C. router(config-if}# ip pim bidir-enable router(config}# ip pim ssm default router(config}# ip igmp version 3
- D. router(config-if}# ip pim sparse mode router(config)# ip pim bsr-candidate Lo0 router(config)}# ip pim rp-candidate Lo0
Answer:
D
Question 14
An engineer must develop a Python script that generates an interface configuration JinJa template
called port_config.j2 with values defined in a Python dictionary
called int_dict. The generated output must be written to a file called port.conf in the same directory
as the Python script. Which line must be added to complete the script and send the
interface configuration generated to a Cisco Nexus switch using SSH?
- A. com =nexus.send_config_from_file(‘commands')
- B. com = nexus.send_config_from_file(‘port.conf')
- C. com =nexus.send_config_from_file('file')
- D. com =nexus.send_config_from_file(‘int_dict’)
Answer:
C
Question 15
Which feature of Cisco Nexus Dashboard permits users to switch between site controllers of Cisco
ACI?
- A. air-gap support
- B. multifactor authentication
- C. single sign-on
- D. cloud-site onboarding
Answer:
D