Questions for the 156-835 were updated on : Dec 01 ,2025
Page 1 out of 5. Viewing questions 1-15 out of 64
Question 1
What is the minimal requirement for a Security Group?
A. 1 Appliance and 1 management port
B. 2 Appliances and 2 ports
C. 1 Appliance and 1 administrator with Multi-Domain admin permissions
D. None, it may be empty.
Answer:
A
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 2
What is the difference between Dual-Site and Multi-Room?
A. Multi-Room is a Single-Site deployment where all Appliances are connected to both orchestrators
B. Multi-Room is a kind of Dual-Site deployment within the same building
C. Multi-Room is Active / Standby and Dual-Site is Active / Active
D. This is the same
Answer:
B
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 3
What cannot be a reason for DETACHED status of Appliance when running asg monitor command?
A. Appliance reboots
B. Appliance is a member of Security Group, but currently disconnected
C. Appliance installed with R80.20
D. There's an issue with Downlink cable
Answer:
C
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 4
There are two 10Gbps dual-port NICs and one 40Gbps NIC installed on a 23800 Appliance in slots 1, 2 and 3 accordingly. Which interfaces should be connected to Orchestrator 1 for downlinks' intra- orchestrator redundancy when using two Orchestrators?
A. Any pair of available ports
B. Port 1 in Slot 2 and Port 2 in Slot 1
C. Port 1 in Slot 1 and Port 2 in Slot 1
D. This configuration is not supported
Answer:
C
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 5
When running ifconfig command on an Appliance, there are interfaces shown in the list: ethl-Sync and eth2-Sync. What is the purpose of these interfaces?
A. These interfaces are bond members (slaves) of Sync Bond
B. These interfaces can be used as backup for Sync interface
C. These interfaces are not in use. Security GW module use Sync interface for synchronization
D. These interfaces represent physical Sync interface at the front panel of appliance
Answer:
D
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 6
What is a downlink interface used for?
A. To connect Orchestrators to customer's infrastructure
B. To connect appliances to customer's infrastructure
C. To connect appliances to Orchestrators
D. To connect in between Orchestrators
Answer:
C
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 7
What cannot be learned from the output of asg monitor command?
A. Appliances cluster status
B. Port status
C. Uptime
D. Security Policy status
Answer:
B
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 8
Where should sx_api_ports_dump,py command be ran?
A. Orchestrator
B. SMO Appliance
C. Management server
D. Security Group
Answer:
A
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 9
What is an uplink interface used for?
A. To connect in between Orchestrators
B. To connect appliances to customer's infrastructure
C. To connect Orchestrators to customer's infrastructure
D. To connect in between appliances
Answer:
B
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 10
What cannot be a reason for "Failed to get remote orchestrator interfaces" error message, when clicking on "Orchestrator" in WebUI?
A. Remote orchestrator has no empty interfaces
B. One orchestrator only, but Orchestrator amount is 2 or no Sync in between orchestrators
C. No Sync between orchestrators
D. Single orchestrator environment, but configured Orchestrator amount is 2
Answer:
A
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 11
What is the max amount of Orchestrators in Dual-site setup?
A. 2 per Security Group
B. 4 per Security Group
C. 2
D. 4
Answer:
D
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 12
Complete the sentence: When using a Break-out cable...
A. All tails of the break-out cable must represent the same type of ports
B. All tails of the break-out cable must represent uplinks
C. Each tail of the break-out cable represent an independent port
D. All tails of the break-out cable must represent downlinks
Answer:
C
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 13
What is the Sync network on Appliances used for?
A. May be used for any purpose, but synchronization always have priority
B. To synchronize configurations and connections in between connection tables of different Appliances
C. To transfer configuration files from Orchestrators to Appliances
D. To transfer data in case of full utilization of the downlink interfaces
Answer:
B
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 14
What kinds of transceivers are supported on Orchestrator MHO-170?
A. QSFP. QSFP28
B. SFP. SFP+. SFP28
C. SFP+, SFP28. QSFP
D. SFP. QSFP, QSFP28
Answer:
A
User Votes:
A
50%
B
50%
C
50%
D
50%
Discussions
0/ 1000
Question 15
In order to set Site (chassis) priority per VS, following command should be used:
A. From given VS context: set chassis high-availability vs chassis_priority
B. From given VSO context: set chassis high-availability vs chassis_priority
C. From any VS context: set chassis high-availability vs <vsid> chassis_priority
D. From VSO context: set chassis high-availability vs <vsid> chassis_priority